|1|| Shubham Tiwari and Sunil Chandel.
NUMERICAL STUDY OF OBLIQUE COLLISION OF A VORTEX RING WITH A HEATED WALL
|Abstract: A numerical simulation is performed for a vortex ring impacting a heated wall at an angle of incidence θ=〖38.5〗^o and Re=1389. The simulation is performed to study the effect on the heat transfer rate due to change in vortex ring structure after it collides with heated wall. It is found that the value of local Nusselt number reaches maximum when region of the ring nearest to the wall is subjected to vortex stretching.|
|2||Sunil Chandel and Pravin Hadgekar.
NUMERICAL ANALYSIS OF ICED WING PERFORMANCE
|Abstract: The present study analyses the effect on aerodynamic performance (Lift and drag coefficients) of NACA 64-008A aerofoil when horn ice is located at 20 degree angle at the leading edge of aerofoil. Coefficient of lift (Cl) and coefficient of drag (Cd) were calculated for angle of attacks from 0 to 4o in increment of 1o using ANSYS FLUENT software. Horn ice configuration reveals that the horn (ice) produces large separated regions about the aerofoil’s leading edge at higher angle of attacks.|
|3|| Prof Sanjay Harip.
EXPERIMENTAL COMBUSTION ANALYSIS OF HOMOGENEOUS CHARGE COMPRESSION IGNITION ENGINE
|Abstract: Homogenous charge Combustion ignition engines are being considered as an alternative to diesel engines. The HCCI engines might be commercialized in light duty vehicles by 2022 as much as half million barrels of oil per day may be saved. Because of the need of reduce worldwide fuel consumption, greenhouse gas emissions, there is strong interest in HCCI worldwide. In this paper we propose a control the stability of the combustion of HCCI engines .|
|4|| Shraddha Popat.
MODELING AND IDENTIFICATION OF ACCIDENT PRONE SPOTS USING GIS
|Abstract: India is experiencing increasing road traffic injuries amidst increasing motorization and urbanization in recent years. Every day, nearly enormous deaths occur on Indian roads and several are hospitalized due to road crashes. GIS have considered to be the emerging trends in revolutionizing traffic analysis and reduction in no. of accidents. This paper also aims to describe a web mapping technique which could act as a assistance in analyzing traffic and reducing no. of accidents.|
|5||Sunil Chandel, Ashwini Kumar and Shubham Tiwari.
COMPUTATIONAL STUDY OF HEAD-ON COLLISION OF TWO CO-AXIAL VORTEX RINGS OVER A HEATED PLATE
|Abstract: This paper provides the CFD analysis to study the effect of head-on collision of two counter rotating vortex rings over a heated plate and the effect of vortex ringlets on the local heat transfer distribution. When two vortex rings collides head on approaching a heated plate then it results in the increase of Nusselt number and thereby increasing the rate of heat transfer. This results in the transfer of the momentum and energy.|
|6|| Nikhilesh Pawar.
IMPROVED DESIGN AND PERFORMANCE ANALYSIS OF GEAR BOX USING CAD/CAM/CAE
|Abstract: Machine tool gear box design is the multi-step analytical procedure converging towards the optimum gear box design. MATLAB programming technique is applied to automate the manual machine tool gear box design process with a greater accuracy & less time. Benefits of the MATLAB programming in design modification are justified. Spur gear design optimization technique, Altered Tooth-sum gearing is included. The proposed design is also validated with CAE tool Ansys.|
|7||Nilavarasan T, Ganapati N Joshi and Sunil Chandel.
ATTENUATION OF FLOW SEPARATION IN A NACA 8410 TURBINE CASCADE USING GURNEY FLAPS
|Abstract: The effect of Gurney Flaps on a NACA 8410 turbine cascade with a blade angle of 30o has been numerically studied. The Flaps were at an angle of 45o with respect to the blade chord. The performance of the cascade at different inflow angles was evaluated with Gurney Flaps of sizes 1% and 2% of the blade chord. The Gurney Flaps increased the lift produced and casued a significant delay in the flow separation. The flaps also induced an increase in the exit Mach number and the flow turning angle.|
|8||Mahesh Kulkarni and Ravindra Ingle.
ACOUSTIC ANALYSIS FOR EFFECT OF EXTENDED INLET AND EXTENDED OUTLET TUBE ON TRANSMISSION LOSS OF SINGLE EXPANSION CHAMBER REACTIVE MUFFLER
|Abstract: Muffler is a device used to reduce noise within the exhaust system. In the present work, an attempt has been made to study the effect of extended Inlet and Outlet elements in Single Expansion Chamber reactive muffler on the muffler’s capacity of noise reduction (i.e. Transmission loss). The acoustic behaviour of the muffler is investigated in detail by: (1) the finite element method by using COMSOL Multi-Physics, (2) and Experimental validation by using Two Load Method.|
|9||Utkarsh Patil and Swapnil Gadgune.
SINUSOIDAL TRACKING ALGORITHM BASED VOLTAGE ORIENTED CONTROL OF HARMONIC LESS RECTIFIER
|Abstract: This paper analyses the operation of rectifier using Sinusoidal Tracking Algorithm (STA). The algorithm is simple and capable of extracting fundamental component. Better current waveform, harmonic less operation, unity power factor, DC link voltage regulation is obtained. Hysteresis Current Controller is used for gate pulse generation. The proposed approach is simulated using MATLAB/Simulink software. Simulation results are presented, which shows validation of proposed control strategy.|
|10||Sheetal Karande, Mahesh Wagh, Sudhir Desai and Sunil Jamadade.
EXPERIMENTAL ANALYSIS OF 100 KG CAPACITY PLASTIC PYROLYSIS PLANT BY USING VANADIUM PENTOXIDE (V2O5) AS A CATALYST
|Abstract: In this paper, the details of pyrolysis process for each type of plastics and the main process parameters that influenced the final product such as oil, gaseous are presented.The catalytic process involved staged catalysis with the aim of maximizing the conversion of the waste plastic to gasoline range hydrocarbons. The oil obtained by pyrolysis process having chemical properties similar as per diesel. The volume of reactor was predicted to process 100kg of plastics.|
|11||Samir Dhatkar and Amarsingh Kanase-Patil.
THERMAL ANALYSIS OF SOLAR AIR HEATER USING POROUS MEDIA AND RIBS
|Abstract: Solar air heater is one of the valuable heat source. The objective of current study is to enhance heat transfer coeffi of SAH. Experimentation has been carried out on SAH consisting SAH with smooth plate, SAH with Porous media, porous media assisted SAH with ribs. Results for Nusselt number, Friction Factor obtained from experimentation were validated using CFD software. It is found that use of porous media and ribs increases thermal performance of SAH compare to smooth plate SAH.|
|12||Pranjal Sakhala, Sanjana Patil, Neha Darade, Pooja Adke and Smita Chaudhary.
SMART ELECTRONIC NOSE SYSTEM FOR MONITORING ORGANIC ABUNDANCE IN SOIL
|Abstract: A rapid increase in world’s population, give rise to significant challenging problems ex. food demand, quality food, etc. The traditional farming techniques decrease the chances to meet global food demand. So providing access to safe and nutritious food is at probable risk. To increase the food productivity and also its quality, monitoring soil abundance plays a key role in organic farming. To solve this problem, an Electronic Nose is designed to monitor soil organic nutrients.|
OPERATION OF SENSORLESS PMSM DRIVE WITH MRAS BASED ESTIMATION
|Abstract: A model reference adaptive system (MRAS) based speed estimator has been used to achieve the sensorless operation of PMSM drive at low and zero speed. In MRAS based estimator PMSM itself used as reference model and current model is used as adjustable model. The method is free from integrator problem and good performance at low speed, independent of stator resistance so less sensitive to parameter. The method is implemented in MATLAB, simulation results show the validity of presented scheme.|
|14||Ambarisha Mishra and Jitendra Kumar.
GENERATION SCHEDULING AND POWER MANAGEMENT OF PEDALING SYSTEM WITH SOLAR PHOTOVOLTAIC SYSTEM
|Abstract: A clean and environment friendly electric power generation with consideration of pedal system and solar energy system is introduced in this paper. The effectiveness of methodology presented here is experimentally verified on the GBPS and obtained energy output is integrated with SPV system. For smooth operation of mechanism a 1:30, turn-ratio gear box is used. A 50 kWp SPV system with GBPS considered in this work. This is a good alternative for the electric power generation with zero emission.|
|15||Dhanashree Pathak and Naresh Chaudhari
RENEWABLE ENERGY RESOURCES
|As we all know that non -renewable energy resources are getting depleted and exhausted day by day there is a need of finding alternatives. Now renewable energy resources here serve to be a perfect alternative which are the never-ending sources of energy such as solar energy, wind energy, hydroelectric energy, biomass which is a term for energy from plants, hydrogen and fuel cells, geothermal power, etc.|
|16||Pradnya Patki, Anjali Rasane and Sudhir Deshpande
STUDY OF THE CONCEPT OF ‘GREEN BUILDINGS’: PRACTICES FROM THE PAST AND ITS APPLICABILITY TODAY
|The paper aims at understanding green building and its interpretation over the years. The objectives are to study green building, to find similarities and differences between different terminologies. The methods used are to summarize understanding from literature review and case examples; to study the similarities between old cultural practices related to climate and new concepts; to understand way of living in the past, needs and today’s fast pace changing lifestyle.|
|17||Mayur Dattatray Khairnar and Sagar Sreekumar Nair.
STUDY ON EGGSHELL AND FRUIT PEELS AS A FERTILIZER
|Abstract: The present study deals with the utilization of eggshell and fruit peels for effective growth of the plant. The aim of this paper is to study and analyse the Carbon, Nitrogen and Hydrogen content from eggshell powder and fruit peels using CHNS Analyzer. This experimental study proves that eggshell powder and Fruit peel powder can be used as fertilizer with no cost bearing as this peels are collected from household waste.|
|18||Balkrishna Chavan, Hradayaprakash Vaidya and Rajani Deogade.
WATER CONDUCTOR SYSTEM FOR MICRO HYDROELECTRIC STATION
|Abstract: Micro hydro power sources are easy to maintain and solution to handle the present problems. Water conductor system for micro power station includes small reservoir, approach channel, power intake, transitions, control structures, pressure shaft, turbines, generator,transformer and power transmission line. Micro hydroelectric units are equipped with essential accurate flow measuring and monitoring sensor mainly for efficiency measurement and maintenance for the optimizing electric energy.|
|19||Adhikrao Patil, Sandeep Kore and Narayan Sane
HEAT TRANSFER ENHANCEMENT IN ROUND TUBE FITTED WITH VARIOUS CONFIGURATIONS OF CIRCULAR RINGS
|In this paper,the effect of various arrangements of circular rings on heat transfer rate in a circular tube was studied with air as working fluid.The tube was fitted with ring inserts of different arrangements as diverging sections,converging sections, converging-diverging sections and inserts with same rings. The highest overall performance factor of 1.26 was obtained for an insert with circular ring of 30% flow blockage area at Re 6,000.|
|20||Gandhar Newaskar, Hemant Bawaskar and Vaishali Limaye.
INTEGRATED SUSTAINABILITY IN HOSPITAL BUILDING
|Abstract: The pressure and harm to the environment caused due to design and operation of Hospital Buildings is substantial, in relation with its energy needs & waste. The Green building also helps in attaining the “ENVISION2030” of UN with total of 17 Sustainable Development Goals. Green Buildings have gained tremendous momentum during the past few years due to awareness and adaptability. Authors have covered integral aspects in present paper titled “Integrated Sustainability in Hospital Building”.|
EFFECTIVENESS OF DAMPERS FOR SEISMIC CONTROL AS EFFICIENT ENERGY CONVERSION SYSTEMS
|Abstract: This paper focus on structural control, nonlinear, seismically excited, 20-story building.Performance of control devices such as PF damper with self-tuning fuzzy control, viscous damper with (FLC) having genetic algorithm base, oil damper with sensors and MR dampers with clipped optimal control is studied. The objective of this is to study optimum energy conversion system . It is found that viscous dampers are effective .Silicone damping fluids are used due to their wide range applications.|
|22||Ganesh Doke, Dhaval Jayawant and Vidyasagar Girmal.
REVIEW OF ENERGY CONSERVATION GUIDELINES ISSUED BY GOVERNMENT FOR COAL FIRED THERMAL POWER PLANT USING ASME PTC 4.0 CODE
|Abstract: Energy Conservation (EC) Act has been introduced to provide the guidelines for the efficient use of energy in India. These guidelines focus on reduction in energy consumption. The Energy conservation guidelines establish the target energy performance values for major energy-consuming equipment, such as boiler, furnace,etc. In this paper, efforts are made to study energy saving in terms of increase in CFBC boiler efficiency by considering EC guideline by analysing a case study.||23||Pooja Kulkarni and G.T. Chavan.
REMOTELY CONTROLLED CAR USING WI-FI
|Abstract: The Internet of things (Io T) is the network of physical devices, vehicles, home appliances. In this paper Io T will be used to control electric vehicle for parameters like acceleration , brake, steering and also provide GPS co-ordinates for updated position of vehicle after interval of every 5000 milliseconds and display images and live stream of video.|
|24||Sidheshwar Murkute, Madan S. H. and Vikram Patil.
PARAMETRIC STUDY OF GREEN CONCRETE AND CONVENTIONAL CONCRETE ON STRENGTH AND DURABILITY PROPERTIES
|Abstract: Green Concrete is a resource-saving structure that reduces environmental impact, carbon dioxide emissions, and waste water. Here comparative evaluation of strength and durability properties of conventional concrete and green concrete incorporating recycled coarse aggregates and fly ash. In the laboratory total of three series of concrete mixtures were prepared. Series I, II and III were prepared with the water to cement (W/C) ratio of 0.3, 0.4 and 0.5 respectively.|
|25||Milind Kulkarni and Dr. P.M. Ghanegaonkar.
DESIGN OF A SOLAR HEATED BIO-DIGESTER FOR IMPROVEMENT IN BIOGAS PRODUCTION
|Abstract: Use of biogas energy can reduce the dependency on fossil fuels and other energy sources. Biogas production is affected by seasonal variations and it can be enhanced by digester heating. Use of solar energy for digester heating can thus bring about the utilization of two renewable energy sources. This paper presents information about the methods of digester heating for getting improved biogas production. The design of an active solar heating system for digester heating is also presented.|
|26||Rashmi Nimbalkar, Rajiv Pazare, Kiran Bhuyar and Vishal Ghutke.
ENVIRONMENTAL PROTECTION AGENCY FRAMEWORK
|Abstract: For more than 45 years, EPA has focused on its mission of protecting human health and the environment by protecting the air we breathe, the water to enjoy and drink and the land to live.Along the way, the Agency has continually honed its research to ensure that the information, innovative tools, and technical solutions EPA delivers match the real-world environmental and public health challenges faced by states, tribes, and communities.|
REVIEW OF RECENT STUDIES ON ALTERNATIVE FUELS FOR INTERNAL COMBUSTION ENGINE
|This paper summaries the use of different alternative fuels of Internal Combustion (IC) engine. It covers the impact of alternative fuels on engine durability, performance, emission of waste products etc. It mainly focus on the history and recent development of bio-diesel, including the different types of bio-diesel, their blends, the characteristics, processing and economics of bio-diesel industry.|
|28||Ganesh Madhikar, Paurnima Pandit, Priyanka Dodke and Pratiksha Dudhal.
A SURVEY ON IMPLEMENTATION OF SMART HELMET
|Abstract: Bike riding is a lot of fun, but accidents happen. People choose motorbikes over car as it is much cheaper to run.Sincce accident percentage of two wheelers are high compared to four wheelers.So wearing a helmet can reduce this number of accidents.This project aims for avoidance of accidents and develop helmet detection system.A module affixed in the helmet, such that, the module will sync with the module affixed on bike and will also ensure that biker has worn Helmet.|
SPECIFICATION OF TESLA MODEL S AND THERMAL MANAGEMENT OF BATTERY
|Abstract: The batteries is the sole power source, large amount of heat is produced which can lead to overheating. In S model Tesla uses 18650 Panasonic batteries which are smaller in size and larger in number it reduces the time for charging to larger extent but it has also a problem of thermal management. The objective is to develop a mathematical model and predicting and investigating thermal behaviour of an electric car battery in response to coolant flow rate and design choices.|
|30||Roshani Wankhade, Amol More, Prasad Inmulwar, Rushab Zade and Rohit Landge.
DESIGN AND ANALYSIS OF THERMOELECTRIC GENERATOR FOR WASTE HEAT RECOVERY FROM AUTOMOBILE EXHAUST.
|Abstract: Energy loss is the crucial bottleneck in the world of automobile. It often rose as crisis all across the globe. Thus for reducing energy consumption various technologies has been invented. As in automobile sector lots of heat energy is getting wasted. Thus the objective of this paper is to utilize the waste heat energy using Thermoelectric Generation. It uses thermoelectric materials that are used to recover the heat. The ultimate aim is to recover the maximum energy in the form of electricity.|
|31||Tushar Patle, Vishwajeet Bhise and Sunil Nimje.
NUMERICAL ANALYSIS ON EFFECT OF ANISOTROPY ON ONSET OF DEBOND AND ITS GROWTH IN ADHESIVELY BONDED COMPOSITE JOINTS
|Abstract: Adhesively bonded composite joints in modern composite structures assembly offers light weight structures, uniform stress distribution, smooth surface contours and excellent fatigue resistance than mechanical fastening. However, the process of adhesive bonding of composite structures can results in manufacturing defects namely debonds.|
|32||Pranita Padwal, Sukruti Pandit, Denisha Vachhani and Sumit Dharmarao
DESIGN OF MECHANICALLY OPERATED FOUR-WHEEL STEERING MECHANISM
|Top selling cars in India,used by major population,are only front wheel steered.It undergoes understeer & oversteer lack of maneuverability,problems in lane changing and speeding,which contributes to accidents. Fourwheel steering helps to eliminate the problems faced.In this paper efforts are made to design a pure mechanical mechanism which allows the driver to switch from Front wheel steering to Fourwheel steering whenever required.|
|33||Vaishnavi Chaudhari, Priyanka Malakmir, Mamta Shahu, Suruchi
DESIGN AND FABRICATION OF MIG MAG MACHINE CARRIER UNIT FOR LOCOMOTIVE WORKSHOP
|This paper aims at designing and fabrication of material handling equipment i.e. MIG MAG welding machine carrier unit for the locomotive workshop. Carrier unit should ease the handling, reduce cost and ensure the safety of the user. A unit has to be designed such that it can be moved to all the corners of the workshop. The carrier unit comprises of inverter, wire feeder, arrangement of two gas cylinders and various accessories. Lightweight material is used for fabrication of the carrier unit.|
BIG DATA ANALYTICS: CHALLENGES, CAPABILITIES AND POTENTIAL BENEFITS
|Abstract: Big Data (BD) sphere is one of the most endowed IT spectrums with sizeable potential both on the surface of maturing economy and design swing in the domain of data storage administration and analytics. The occupied prospects of BD Analytics can be achieved through the definition of technologies that bring about BD users' outlook and requirements. Under these grounds, authors discuss issues and challenges from the Data Analytics design and development perspective.|
|35||Sudnya Rale, Aishwarya Shelke, Aditi Shinde, Vaibhavi Shewale and Satish Silaskar.
DESIGN AND FABRICATION OF HUMAN POWERED FORKLIFT
|Abstract: The purpose of this paper is to find best possible design of forklift which offers the simplest and cheapest way with reduced human efforts. The observation results into some notified problems, which resolve by some improvements for making it user friendly.The aim is to design and fabricate manual stair climbing forklift which can carry loads upstairs with less effort. Based on research new design offers improvised feature which is used to lift 150kg with fork and 60kg by hook.|
|36||Dadabhau Karanjule, Dr. Sunil Bhamare and Dr. Thota Rao.
INVESTIGATING SPRINGBACK OF SEAMLESS TUBES COLD DRAWING PROCESS USING DESIGN OF EXPERIMENTS (DOE) AND MICROSTRUCTURAL INVESTIGATIONS
|Abstract: Cold drawing for production of seamless tubes is widely used and Springback is one the defect occurring in it.In this work optimized parameters to minimize springback viz.,reduction ratio, die semi angle,land width and drawing speed through Design of Experiments and microstructural investigations are obtained which are 10-15 % reduction ratio,15 degree die semi angle,10 mm land width and 8 m/min drawing speed for ST 52 tube material and AISI D3 die-plug material.|
|37||Anil Parlikar, P D Dahe and Kalpeshkumar M Sharma.
OPTIMIZATION OF RESERVOIR OPERATION – A CASE STUDY OF UDUTHOREHALLA RESERVOIR IN INDIA
|Abstract: The Linear Programming (LP) and Genetic Algorithm (GA) have been used in the present study for the reservoir operation of Uduthorehalla Project, located in Cauvery Basin in Karnataka, India. The annual reservoir yields are computed using LP and GA techniques. The effect of linear and non-linear relationship of reservoir storage and water surface area on reservoir yield is assessed. The 100% and 75% reliable yields are obtained for the present reservoir system using LP and GA.|
|38||Md Anoarul Islam, Manabendra Maiti and Judhajit Sanyal.
REGRESSION-BASED PREDICTIVE MODELS FOR ESTIMATION OF ELECTRICITY CONSUMPTION
|Abstract: The estimation of electric power consumption is an integral part of power generation economics and is critical to optimization of cost of production of electricity, since it allows demand matching for optimized generation of electricity. The present paper augments a simple regression-based scheme with a predictive machine-learning based piecewise linear slope-estimation technique for more accurate estimates, which is further modified to compensate for initialization error.|
|39||Trupti Chavan, Priyanka Chaugule, Pratiksha Vishwasrao and Pravin Alone
DESIGN OF COMPONENTS OF AIR POWERED VEHICLES
|The paper focuses on the design procedure and calculations of the main components of the compressed air vehicle.To reduce the emission of harmful gases from conventional vehicles, the use of a compressed air as fuel is the one alternate way.It can be used to travel on small campuses like an airport, golf ground, industrial areas, etc.Some more technologies are needed to introduce which will improve the performance of the compressed air engine.|
|40||Anal Sheth and Debasis Sarkar.
Review & qualitative assessment of biodiesel as an alternative fuel for bus transport
|Abstract: This article provides a state of art review on international research and practices on biodiesel usage for transport and the national policy of biofuels – 2018 by the Government of India. A qualitative assessment of biofuels based on twenty indicators has been performed. The findings conclude that at this point of time the use of biodiesel for bus transport in India poses numerous challenges and is not feasible at the scale of urban bus transit operation.|
|41||Tukaram Gilbile, Sambhaji Pawar and Rahul Kamble
DEVELOPMENT AND PERFORMANCE EVALUATION OF SDC-GDC COMPOSITE ELECTROLYTE FOR LOW TEMPERATURE SOFC APPLICATION
|The fuel cells are clean and efficient mode of energy generation which directly converts chemical energy into electrical energy. Solid oxide fuel cell (SOFC) obstructs its applicability because of its high operating temperature and unstable performance at normal operating conditions. Thus, in the present investigation attempt has been made to enhance the performance SOFC electrolyte by forming the composites of SDC and GDC at low temperature.|
|42||Amrut Godse, Sambhaji Pawar, Rahul Kamble and V Kapatkar
STRUCTURAL AND ELECTRICAL PERFORMANCE STUDY OF DOPED SDC SAMPLES FOR SOFC APPLICATION
|High operating temperature (800 to 1000 oC) of SOFC is a main hurdle to reduce cost, material selection and to increase operation time. High electrolyte polarization resistance effectively commands on the operating temperature of whole solid oxide fuel cell. Hence in this work co-doping in ceria electrolyte (SDC) was successfully achieved to polarization resistance and increases the oxygen (O2-) ion conductivity at low temperature.|
|43||Makarand Jadhav and Abhiraj Eksambekar
CASE STUDY: DRONE TO FLUSH OUT ROUTE TRAFFIC FOR EMERGENCY VEHICLES
|To provide emergency services to patients by reaching hospitals in time,a Drone based system is proposed to clear route with reference to available traffic data.This system is able to clear road traffic by 50%. It will help the emergency Vehicles to reach faster and can extend services to patients. This in turn saves human life in metropolitan cities. The system design is based on image analysis in measuring traffic densities at various squares.|
|44||Tusharkumar Mali, Jitendra Shinde and Dhananjay Khankal
MINIMUM QUANTITY LUBRICATION IN MACHINING -A REVIEW
|Minimum quantity lubrication (MQL) serves as an alternative to conventional cooling by reducing the volume of cutting fluid used in the machining process. The environment is also protected and possible health hazard for the machine operator. With MQL the machining cost can be minimize significantly. The adverse health effects caused by the use of coolants.The objective of this paper is to review the state of the art in MQL with particular focus on turning, milling machining operation.|
|45||Essha Shinde, Sanjana Kulkarni and Charushila Sarate
DESIGN OF LIGHT GENERATING MECHANISM USING GRAVITY
|Abstract: The concept proposed in this paper also fundamentally converts mechanical input to generate electrical output to power an LED source. The major difference is that it uses gravity as an input. The mechanism operates on gravitational force which is converted into electrical output that powers an LED source|
|46||Makarand Jadhav, Abhiraj Eksambekar, Akansh Belchada and Yash Lawale.
IMPLEMENTATION OF AUTONOMOUS FIRE COMBAT TURRET
|Response time of conventional fire combat needs to be reduced.The time lag to identify and initiate actuation protocol is compromised.The arrival of fire brigade further reduces the damage.An efficient fire combat system is design and developed to reduce problems.This system extinguishes fire before it reaches its destructive level and eliminates flaws by raising an alarm.Further 70% accuracy is achieved to detect fire with image processing techniques.The response time of system is 2-4 sec.|
|47||Makarand Jadhav, Akshata Kanade and Pooja Kamble.
GSM BASED SOCIETY MONITORING SYSTEM
|GSM based society monitoring system is used to control the parameters related to human comfort with sensor based automation. This system is designed for automatic switching of water pump after detection of water level in the tank, parking light management with PIR sensor, supervising and tracking watchman with help of image processing method. Garbage management is included to maintain cleanliness.|
|48||Shubham Bhoskar and Sanjay Patil.
A COMPARATIVE STUDY OF SINGLE POINT DIAMOND DRESSER AND MULTI POINT DIAMOND DRESSER FOR GRINDING WHEEL: A REVIEW
|Grinding is used mainly for finishing metal component and it is last stage. The main objective is to generate quality surface on the component. Grinding wheel is consisting of the many abrasive particles. Dressing is a process which remove loaded surface of grinding wheel and makes it sharp. There is a single point and multi- point dressers are there. Multipoint diamond dresser has certain advantages the single point diamond dresser.|
|49||Vedant Sutaone, Shirish Pisal, Chetana Chaudhari, Suwed Pawar and Vishwanath Kapatkar
PARAMETRIC INFLUENCE OF ULTRASONIC PLASTIC WELDING ON WELD STRENGTH OF ACRYLIC, POLYCARBONATE AND POLYPROPYLENE MATERIALS
|Ultrasonic welding is the most widely used and fastest known welding technique for joining thermoplastic materials. The process uses ultrasonic energy at high frequencies (20-40 kHz) to produce low amplitude (1-25m) mechanical vibrations. These vibrations generate heat at the joint interface of the parts being welded, resulting in melting of the thermoplastic materials and after cooling weld formation takes place.|
|50||Vedant Sutaone, Shirish Pisal, Chetana Chaudhari, Suwed Pawar and Vishwanath Kapatkar
EFFECT OF ULTRASONIC WELDING PARAMETERS ON WELD STRENGTH OF THERMOPLASTIC MATERIALS USING TAGUCHI METHOD
|The ultrasonic welding process is not only a well-known industrial joining process but it has also been a dynamic research area. Materials ranging from metals to non-metals are easily welded using this welding technique. Some research has already been carried out but the more extensive analysis is needed on ultrasonic welding of thermoplastics.|
|51||Prof. Swati Bhonde, Shreyas Jejurkar, Simran Inamdar, Nikita Kale and Sayali
AUTOMATIC QUESTION PAPER GENERATION USING MACHINE LEARNING APPROACH
|It is very challenging to generate quality question paper.To avoid repetition of questions and semantically same questions we are using machine learning algorithms in our system.|
|52||Arati Pradhan and Saswati Sahoo
GREEN COMPUTING : A STEP TOWARDS SUSTAINABLE DEVELOPMENT
|Sustainable development is based on the three pillars of sustainability: economic, environmental and social sustainability. In IT sector at each stage starting from manufacturing a system till the end of its life cycle, a computer impacts and contribute the causes of environmental problem. In this paper we have highlighted on the implementation of Green Computing to enhance sustainability.|
|53||Pratik Raut, Shrutika Phadatare, Sanket Raikar and Sonali Sanap
REVIEW ON EFFECT OF BLADE SHAPE ON PERFORMANCE OF SAVONIUS VAWT FOR ACCESSING POWER PERFORMANCE
|Louder noise at the location, collision of bird species with blades are the drawbacks of HAWT which can be overcome by vertical axis wind turbine while fulfilling the energy needs. So, the main objective of the project revolves around the design of Savonius type vertical axis wind turbine and its comparative analysis for four different blade shapes to improve the performance and starting characteristics.|
|54||Mahesh Khade and Dattatray Rajmane
A REVIEW OF ARTIFICIAL NEURAL NETWORK IN RAINFALL- RUNOFF SIMULATION
|Artificial neural network (ANN) working as a universal predictor,the concept of ANN was 70 years old but due to lack of technology its use in various fields was limited. From last three decade with revolution of technology researchers has applied this technique in various fields of engineering and sciences. In field of Civil Engineering researchers successfully applied this technique in Hydrology. This paper consists of literature review of ANN in rainfall-runoff simulation.|
|55||Sagar Mohalkar, Omkar Nawale, Sanket Wable and Shubham Naikwadi
A NOVEL APPROACH FOR CROP MONITORING AND DISEASE PREDICTION USING IOT
|Indian farmers have adopted manual observation based techniques which has resulted in either excessive use of pesticides or under use of watering which results in less productive crops.To implement system which automatically monitor the crops from planting to harvesting and Predict the Diseases using IoT, developing IoT based system which will give notifications to farmer about the requirements of the particular crop, information about irrigation cycle,fertilization required for crops.|
|56||Yugendra Chincholkar, Abhijeet Bagade, Vaibhav Chaudhari and Mangesh Kapadi
SECURE AUDIO STEGANOGRAPHY ALGORITHM BASED ON DCT & DWT WITH OTP ENCRYPTION
|Today’s rapid development of the internet makes transactions message even more comfortable and faster. The problem in the transaction messages is security when private and secret. Security of messages is done with steganography. It is a way to hide messages into other content. The main challenge for algorithm development is to secure data with good quality. So, we have proposed steganography techniques using DCT & DWT along with using the one-time password.|
|57||Prof. Swati Bhonde, Jyoti Kakade, Monali Boste, Ruchika Bharati and Suvarna Chakor
MACHINE LEARNING BASED MODEL FOR BREAST CANCER DETECTION
|Machine Learning techniques can be used to develop tools for physicians that can be used as an effective mechanism for early detection and diagnosis of breast cancer which will greatly enhance the survival rate of patients.|
CHALLENGES AND OPPORTUNITIES FOR CREATING A SUSTAINABLE GLOBAL MARKET FOR ELECTRIC VEHICLES
|This review paper takes an in-depth look at the challenges faced by the global automotive market with the mass adoption of electric vehicles. A review of the vehicle lifecycle (with corresponding energy expenditure and emissions) is made. Results from studies around the world are presented, followed by a review of the strategies for introducing EVs to the global automotive market in an environmentally and economically sustainable manner. Migration toward renewable sources of energy is necessary.|
|59||Kunal Thanekar, Shradha Kalburgi, Neha Kesare, Santosh Kushwah and Sagar Choudhari
REVIEW PAPER ON TREATMENT OF GREY WATER USING LOW COST TECHNOLOGY
|As due to increase in population, water demand has also increase which has led to the idea of using grey water as a source of water. Grey water is a waste water generated from household, office buildings and streams. By applying proper treatment grey water can be reused for other purposes. This paper presents a review of existing low cost technologies for treatment of grey water.|
|60||Ghulam Ali Amiri
ROUTING ISSUES IN INTERNET OF THINGS (IOT): A SURVEY
|This paper states the routing issues in the Internet of Things (IoT). The main point of focus is especially routing protocols in IoT and wireless sensor networks (WSN). “Everything which is connected to the internet is alive”, is going to be the new rule for future. Future is the Internet of Things (IoT), the world is changing every day with new technologies and inventions. Internet of Things (IoT) has known as a future scenario of technology in human life.|
|61||Yugendra Chincholkar, Arati Gaikwad, Devyani Dongre and Anjali Algule
LIQUID LEVEL MEASUREMENT USING DIGITAL IMAGE PROCESSING
|Liquid level measurement is used in many fields. Contact and non-contact are types of level measurement techniques. This is are sensitive, tend to probe erosion, influenced by turbulence and produce an error in the level measurement. This paper provides a measuring method by using a fully automated computer-based non-contact level measurement using image processing. Its robust against environmental conditions, and it fails proof against component failure.|
|62||Zohra Sahak and Khoshal Rahman Rahmani
MOBILE AD HOC NETWORK, PROPERTIES, ROUTING PROTOCOLS AND SECURITY ATTACKS
|Last few years wireless communication has grown and still, it is an area of interest to a large number of researchers. MANET consists of mobile wireless nodes. The communication between these mobile nodes is carried out without any centralized control. MANET is a self-governing system consisting of a collection of a mobile node. MANET is kind of infrastructure less network which is self-configurable in nature each node is able to move an arbitrary network topology.|
|63||Mitali Markande, Mrunmayi Bhide and Jayashree Prasad
REVIEW OF BLOCKCHAIN BASED E-VOTING SYSTEM
|Democratic voting is a crucial and serious event in any country.|
|64||Ms. Swati S. Kate and V. B. Pansare
REVIEW ON DETERMINATION OF BEST JOINING METHOD FOR GFRP BY USING EXPERIMENTATION AND FEA ANALYSIS
|Applications of Composite materials are used in the various Fields. Due to the high mechanical strength they are widely used in the low weight requirement and also used as a suitable alternative to metals. Most of the applications use either adhesive bonding or mechanical fasteners for joining composite materials.Automobile industries are exploring composite materials usage by replacing the conventional one because of light weight properties reduces the vehicle weight.|
|65||Devraj Pimputkar, Vikrant Bhagat, Omkar Patil and Amar Gavhane
LITERATURE REVIEW ON DESIGN OF ENERGY DISSIPATION TYPE STILLING BASIN
|Hydraulic jump type energy dissipaters are widely used techniques of energy dissipation while designing the hydraulic structures like dams, weirs and barrages. They are popular for their simplicity and efficiency. Local scour downstream of hydraulic structures due to hydraulic jump is considered one of the tedious and complicated problems facing their stability. This research document discusses the literature related to hydraulic jump type stilling basin.|
AVIATION TO SUPPORT SUSTAINABLE DEVELOPMENT
|Global aviation is a catalyst to sustainable development.|
|69||Shailesh Gavalkar and Dr D. G. Thakur
FINITE ELEMENT ANALYSIS OF STEERABLE AXLE TRAILER CHASSIS WITH HYDRAULIC SUSPENSION
|Steerable Axle trailer with hydraulic suspension in modern transportation is used for safe transport of heavy and oversized cargo which cannot be transported on regular vehicles.In this paper, FEM analysis of the trailer structure is carried out for static load case and results will be interpreted. The modeling of the trailer is carried out in SOLIDWORKS and meshing/structural analysis in HYPERMESH software.|
|70||Sai Chandra, G. B. Radhika and Sv Satyanarayana
KINETIC STUDY ON ADSORPTION OF COPPER USING GRAPHENE OXIDE (GO)
|In this paper batch removal of Copper from aqueous solutions by Graphene Oxide (GO) was investigated. The batch experiments were conducted to study the adsorption kinetics of cu removal for the concentration of 10 mg/L cu solution. Batch mode experiments were carried out as a function of adsorbent dosage and contact time. Maximum percentage of Copper removal was found to be 80 % at 4.5 gms of adsorbent. SEM, TEM, FTIR and Raman Spectroscopy were done.|
|71||Makrand Kakatkar, Priyanka Gaikwad and Makarand Jadhav
ADAPTIVE FUZZY CONTROL FOR NONLINEAR CONTROL SYSTEM
|Solving nonlinearity problem in signal processing for robotic manipulators is critical.All objects are fuzzy and uncertain. The processes are difficult to describe with precise mathematical model. To design a Robotic Arm is a problem of nonlinear multivariable system with inherent instability.It is control with fuzzy approach with fuzzy inference system in MATLAB.System is adaptive by connecting encoders to motor give feedback.|
|73||Amar B Deshmukh and Dr. N Usha Rani
REVIEW ON MULTI VIEW FACE VIDEO SUPER RESOLUTION METHODS
|Resolution of the image is one of the main concerns of image quality. Higher resolution is required in most of the applications, because higher resolution means more details in the image. The use of better image sensors and optics is an expensive and also limiting way of increasing pixel density within the image. The use of image processing methods, to obtain a high resolution image from low resolution images is a cheap and effective solution.|
|74|| Ketan Adsure and Madan Mali
DESIGN OF BAND GAP REFERENCE CIRCUIT FOR SUB 1-V OPERATION WITH LOW SUPPLY VOLTAGE
|In design of an analog VLSI circuits it is important to create current and voltage reference circuits. This Band Gap Reference (BGR) is proposed to successfully operate at sub-1V with supply voltage of 1.2V . The main intention of this paper work is to explore the performance and design of BGR. BGR circuit which is capable of producing constant output voltage for given supply voltage is implemented. The testing of MOSFET device for process corners is presented.|
|75|| Amruta Chavan and Makrand Kakatkar
AUTOMATIC FRUIT SORTING AND QUALITY ANALYZER
|Fruit is essential for sustenance and nourishment of life. The fruit sorting system gives us various information like shape,color,size etc. In present days the grading and classification is performed based on through experience and observations i.e. manually. In this project, system is designed for sorting and analyzing the quality of fruit and it is implemented through MATLAB.The system utilizes image-processing techniques and embedded system to analyze the quality and sort the fruits.|
|76|| Anand Vedapathak and Sachin Takale
IMPLEMENTATION OF HIERARCHICAL ROUTING PROTOCOL FOR WSN
|In a WSN a node is not useful when its battery dies,so to avoid this problem hierarchical routing protocols were introduced.LEACH protocol is analyzed,with its phases,advantages,disadvantages & also various kinds of attacks on this routing protocol.The main goal of cluster-based sensor networks is to decrease system delay and reduce energy consumption.Leach is a cluster-based protocol for micro sensor networks which achieves energy efficient,scalable routing & fair media access for sensor nodes.|
|77|| Poonam Badadhe and Shailendra Badwaik
IMPLEMENTATION OF 1000 BASE-X PHYSICAL CODING SUBLAYER (PCS) USING VERILOG HDL
|This paper aims at implementing a physical layer networking protocol, 1000Base-X Physical Coding Sublayer (PCS) using Verilog HDL. The functionality of PCS is specified is IEEE 802.3 standard. The proposed design is implemented in Xilinx ISE 14.7.|
|78|| Pranamika Paul and Y. D. Chincholkar
METRO MASS TRANSIT AUTOMATION
|More populated country use public transportation more frequent than other countries, passenger who use these services suffer from some kind of issues . In this system they use travel card that has unique number which is converted to a serial number and used for faring purpose for unique identification. Here we use RFID integrated in a card and it is called as travelling cashless card here.|
|79|| Rushi Chaudhari, Rohan Rane, Vedang Pingle and Rohan Marathe
DETECTION OF DISEASES IN TOMATO PLANTS USING DEEP LEARNING
|The proposed system aims to serve as a tool for the farmers to identify diseases in tomato plants, using a smartphone application as a means of interface and a CNN for identification of diseases in real time. Processing and storage constraints are eliminated with the use of Cloud platform. We also aim to make the application more comprehensive by suggesting the remedies and preventive measures for the detected disease.|
|80|| Atharvan Boxey and Madan Mali
LVDS DESIGN FOR HIGH SPEED APPLICATION
|The devices are getting smaller due to decrease in feature size this small size makes them more area efficient as well as they operate at very high speeds, So in order to suit such a scenario while data transmission a communication protocol must be present. LVDS is a used for transmission of binary data over copper cable. This project not only designs a LVDS but also aims to provide a better speed and less power consumption as compared to its previous implementations in |
|81|| Shubham Suke and Pushpa Bangare
DESIGN LBIST USING STUMPS ARCHITECTURE
|The rapidly increasing complexity of IC designs makes testing of VLSI chips more difficult due to occurrence of faults in the VLSI chips. This lead to development of testing technology called Logic Built in Self-Test (L-BIST).Self-Test Using MISR/Parallel SRSG (STUMPS) architecture is used in logic BIST. The main intention of this paper work is to understand the performance and design of LBIST using STUMPS for VLSI IC testing and analyzing speed, fault coverage and power|
|82|| Mohini Deore and Vrushali Raut
DESIGN OF RECEIVER CONTINUOUS TIME LINEAR EQUALIZER FOR HIGH GAIN
|This paper presents a design of continuous-time linear equalizer for 4 dB equalization at 1GHz frequency.Digital SERIALIZER / DESRIALIZER circuit contains the continuous time linear equalizer which compensates for the high frequency loss of electric channels.The objective is to design the continuous linear time equalizer circuit and to analyze the circuit performance.For the project all the circuits are being implemented in 45nm CMOS technology|
|83|| Amruta More and Sashikala Koti
DESIGN AND VERIFICATION OF APB PROTOCOL FOR LOW BANDWIDTH SFR READ/WRITE USING UVM
|In this paper Advance Peripheral Protocol (APB) includes inter connection specification for the connection and management of various functional blocks like IP's in SoC. It is used for low cost interface with minimum power consumption and reduced interface complexity. UVM is used for verification. and SFR read and write operation is performed.|
|84|| Pritam Borate and Shashikant Lokhande
SMART FOOD DISPENSING MACHINE
|India is home to largest number of malnourished children. Major causes for malnutrition in India is economic inequality.Millions of children’s sleep hungry across India, as they do not have money nor work to get money to buy food to eat and live happily. We therefore intended to provide a solution by constructing food-dispensing machine, which dispense food to needy people. People who insert bottle in machine can have choice to select option to have packed dry food, reward money or grain.|
|85|| Saloni Sonawane and Rupali Pawar
IOT BASED SMART GREENHOUSE AUTOMATION USING ATMEGA
|86|| Bhupender Rawal, Himanshu Panda and Sunil Chandel
VIBRATIONAL ENERGY HARVESTING CAPABILITY OF LEAD-FREE PIEZOCERAMICS
|This study elucidates the properties of different sodium potassium niobate based lead free piezoceramics prepared by solid state reaction method. The lead free piezoceramic with optimum properties is utilized to fabricate a vibration energy harvesting set up. The output voltage generated by the module was found to be dependent on the ‘g’ force experienced by the module and frequency of vibration.|
|87|| Bhupender Rawal, Himanshu Panda and Sunil Chandel
POLING ENGINEERING OF SODIUM POTASSIUM NIOBATE BASED LEAD-FREE PIEZOCERAMICS
|The influence of poling conditions on the crystal structure,dielectric and piezoelectric properties of (Na0.495K0.455Li0.05) (Nb0.95Ta0.05)O3 ceramics, prepared using solid state reaction route, has been reported. The piezoelectric properties were found to be affected substantially by poling condition. Optimum piezoelectric properties with the lowest aging rate and good thermal stability up to 120 ºC was found in samples sintered at 1140 ºC and poled at 120 ºC poling temperature.|
|92|| Shubhankar Shinde, Vipul Sonawane, Dr. Amar Pandhare, Sanket Shinde
DESIGN AND OPTIMISATION OF AQUA-SILENCER
|An aqua-silencer is a device which uses activated carbon and water of lime to not just reduce the emissions but also noise level. It is connected at the exhaust of the engine. When gases pass through the system, the activated charcoal absorbs most of it and the remaining reacts with the lime water and hence emissions are reduced. As sound is less audible in liquid medium hence noise level is also reduced in the system. It is economic, easy to maintain and a sustainable device.|
|94|| Anita Patki, Rajendra Goyal, Rohan Saraf and Himanshu Patil
REVIEW PAPER ON THERMOMECHANICAL AND DIELECTRIC PROPERTIES OF POLYMER NANOCOMPOSITES
|This review paper deals with the preparation and characterization of nanocomposites of poly(ether ether ketone) (PEEK) containing various fillers like silicon nitride (Si3N4) aluminum oxide (Al2O3) and aluminium nitride (AlN) fillers. Thermogravimetric analysis showed enhanced thermal stability and char yield on increasing the filler content. The results show that the PEEK nanocomposites may have potential applications in electronics.|
|95|| Shantanu Debnath, Dheeraj Kumar and Abhijit Sarkar
AN AHP-MOORA BASED PERFORMANCE IMPROVEMENT OF ELECTRO DISCHARGE MACHINING PROCESS ON AL-CU-SIC COMPOSITE
|In the study AHP-MOORA adopted to find the efficiency of optimizing multiple performance characteristics for EDM of Al-4.5%Cu-SiC composite.The influence of three machine process parameter pulse on (TON), peak current, duty cycle and one material variable weight fraction on the response variables MRR,EWR and SR have been investigated using multi-attribute decision-making model.The method implemented in this paper is advantageous.|
|96|| Arjun Patil
OCEAN ENERGY AND ITS HARVESTING
|This paper focuses on the idea of getting benefited by one of the largest sources of renewable energy source by absorbing its energy in the form of marine and tidal current energy, thermal energy, wave energy etc. This paper will also give us a perspective of how harvesting of the ocean energy would change the traditional energy production business with respect to economy, efficiency and its effect on nature.|
|88|| Raushan Kumar, Saurabh Chandel, Vaishnavi Shisode and Rupali Pawar
WATER QUALITY MONITORING SYSTEM BASED ON IOT
|89|| Amey Guthe, Nikhil Hole, Shubham Jagtap and Rupali Pawar
REVIEW OF ATTENDANCE MARKING SYSTEM USING FACE RECOGNITION AND CLOUD
|90|| Monis Raja, Atharva Mantri, Pratik Morey and Dr. Sanjay Ganorkar
VISION-BASED DROWSINESS DETECTION
|91|| Bruhaspati Mane and Sanjay Ganorkar
ANN BASED APPROACH WITH APPLICATION FOR BRAIN COMPUTER INTERFACE
|93||Makrand Kakatkar and Priyanka Gaikwad
FUZZY CONTROL FOR NONLINEAR CONTROL SYSTEM